🚁 Professional FPV Drone Systems · Components · OEM / ODM Solutions
Support@skyvoltfpv.com  |  WhatsApp  |  ☎ +86 18938645876  |  🌐 EN
Guide

CADDX Ascent GT Pro Z-40 VTX (4W): Specs, Features & Setup Guide for Long-Range Walksnail FPV

by SkyVolt FPV Engineering Team · About the authors

CADDX Ascent GT Pro Z-40 VTX (4W): Specs, Features & Setup Guide for Long-Range Walksnail FPV

Meet the CADDX Ascent GT Pro Z-40, a powerful 4W Walksnail digital VTX built for long-range FPV, racing and cinematic drone flights. Check its key specs, latency, power requirements, installation tips and critical safety notes.

If you are chasing reliable long-range FPV, clean high-definition video and rock-solid signal penetration, the CADDX Ascent GT Pro Z-40 VTX 4W deserves your attention. This high-power digital video transmitter and camera combo sits inside the Walksnail Ascent digital FPV ecosystem, engineered specifically for long-range drones, competitive racing and aerial filming.

Unlike low-power digital VTX options that struggle when you push distance or fly through obstacles, the Z-40 cranks up transmit power while keeping the crisp digital HD picture and low latency that Walksnail pilots love.

Core Specifications & Key Features

Let’s break down the hardware specs of the CADDX Ascent GT Pro Z-40:

Output Power: Up to 4000 mW (4W) high-power transmission for extended flight range and stronger signal penetration through trees and terrain.

Video Modes: Digital transmission supporting 1080P @ 60fps or 720P @ 100fps. Great for smooth cinematic footage or high refresh-rate racing.

Frequency Band: 5.650 – 5.924 GHz (5.8 GHz digital system).

Latency: Low-latency performance, averaging roughly 22 ms to 35 ms, varying by selected video mode.

Power Input: Wide operating voltage from 11.1 V to 25.2 V, compatible with 3S–6S LiPo batteries. At high output, it draws approximately 1.5 A at 12 V.

Physical Size & Mounting: The main board is roughly 30×30 mm, or 34×34×22.6 mm for the full assembly. It supports 20×20 mm and 25.5×25.5 mm mounting hole patterns. The companion camera module measures around 14×14×19 mm.

Flight Controller Integration: Fully compatible with Betaflight 4.4 / 4.5 via UART MSP and VTX DisplayPort for HD OSD. Firmware updates can be completed over Type‑C using the official CADDX PC Tool.

Antenna Design: Dual-antenna architecture to improve signal coverage, reduce dropouts and boost overall link stability.


 Who Is This VTX For?

The Ascent GT Pro Z-40 is not a tiny-whoop lightweight unit. It is built for pilots with specific goals:

✅ Long-range cruising pilots: The 4W power gives you extra reach when flying across open spaces.

✅ Cinematic & content creators: 1080P 60fps digital feed delivers sharp detail for scouting shots and recording aerial footage.

✅ Freestyle & race pilots: Low latency and 720P@100fps mode keep your view responsive for tight, fast flying.

✅ Pilots flying in moderately cluttered environments: Higher transmit power helps push the signal past foliage and light obstructions.


It is best paired with 5–7 inch builds that have adequate space for cooling and a robust BEC capable of handling peak current draw.


 Important Notes & Critical Precautions

This is a high-power VTX, and there are non-negotiable points you must follow before and during flight:

1. Cooling is mandatory

At full 4W output, this VTX generates a lot of heat. Sustained, adequate airflow is required to prevent overheating, thermal throttling or permanent hardware damage. Do not run it at maximum power in a fully enclosed shell without proper cooling.

2. Check your power supply / BEC

Your drone’s BEC or power circuit must reliably supply the peak current the system draws. Insufficient power will trigger sudden disconnections mid-flight, which can lead to lost drones. Always verify current capacity before your first flight.

3. Never power on without antennas installed

Always mount and securely fasten both antennas before applying power to the VTX. Powering the transmitter with no antenna connected can instantly burn out its RF amplifier components and void your hardware.

4. Local radio regulations

Before using high-power 5.8 GHz transmitters, confirm that 4W transmission is legal and permitted in your country or region. Many areas enforce strict power limits for unlicensed FPV radio equipment.


 Final Thoughts

The CADDX Ascent GT Pro Z-40 fills a nice gap in the Walksnail ecosystem: a high-power digital VTX for pilots who want more range and penetration without switching back to analog video. If you are tired of digital link dropouts on your long-range rig and your frame, power system and cooling setup can handle the extra heat and current, this is one of the most compelling upgrades available.

If you prioritize ultra-light weight for tiny whoops or indoor racing, a lower-power VTX will be a better fit. But for long-range, freestyle and aerial filming pilots ready to max out their digital FPV link, the Z-40 is a serious contender.

Request a Quote ← All Resources

Keep Reading